The success of scaffolding cuplock lies in its principal design features:
|
|
 |
 |
 |
 |
 |
 |
   |
 |
 |
|
 |
Standard / Vertical |  |
||||||
|
||||||||
|
Cuplok spigotted standards are principally used in
access scaffolding applications and also as a base structure for
formwork support applications. They have cup joints at 500mm intervals.
The captive mobile top cups are designed to endure rough site handling
and welded bottom cups are made from high-quality steel. Integral
spigots, 150mm long, are provided at the top of each standard for making
vertical connections. The spigots and the base of each standard
incorporate 16mm dia. holes to enable use of locking pins to join
standards where necessary.
Size:
Scaffolding Cuplock Standard 0.5m Scaffolding Cuplock Standard 1.0m Scaffolding Cuplock Standard 1.5m Scaffolding Cuplock Standard 2.0m Scaffolding Cuplock Standard 2.5m Scaffolding Cuplock Standard 3.0m |
||||||||
 |
|
 |
|
Ledger / Horizontal | |
||||||
|
||||||||
|
The Ledgers are manufactured from 48.3mm O.D. tube
with forged steel blade ends which locate into bottom cups of the
standards and are locked in place by the corresponding top cups. Ledgers
are available in various lengths to provide the desired grid dimension
for scaffolding or formwork. Production of the ledger since 1997 has
been from thinner high grade steel tube. This contributes to a higher
ledger for easier handling. Ledgers manufactured prior to 1997 are made
from the thicker wall tube and weigh approx. 20% heavier than the
weights stated below.
Size:
Cuplok Ledger 0.6m Cuplok Ledger 0.9m Cuplok Ledger 1.2m Cuplok Ledger 1.25m Cuplok Ledger 1.3m Cuplok Ledger 1.5m Cuplok Ledger 1.6m Cuplok Ledger 1.8m Cuplok Ledger 2m Cuplok Ledger 2.5m |
||||||||
|
|
|
|
Cuplock Transom | |
||||||
|
||||||||
|
Transmos are fabricated from twin structural angles
fixed back to back with a drop forged blade attached to each end. The
2.44m Transom has an additional web member welded below the flange
section for added strength. The transom blade locates into a bottom cup
and is locked in position by the top cup. The outward standing bottom
leg of the angles supports the steel planks in a captive manner.
Available in various lengths to suit scaffolding and formwork
applications. Size Cuplok Transom 0.31m Cuplok Transom 0.61m Cuplok Transom 0.83m Cuplok Transom 1.05m Cuplok Transom 1.27m Cuplok Transom 1.83m Cuplok Transom 2.44m |
||||||||
|
|
|
|
Cuplock Omega Transom | |
||||||
|
||||||||
|
Omega Transoms manufactured from press bent section with flange type extensions on both sides provides a strong support for working platform with Cuplock steel battens. Size:
Cuplock Omega Transom 0.9 M Cuplock Omega Transom 1.3 M Cuplock Omega Transom 1.8 M Cuplock Omega Transom 2.5 M |
||||||||
|
|
|
|
Cuplock Intermediate Transom | |
||||||
|
||||||||
|
For use with Hop-up brackets where distance
between standards exceeds the span of scaffold boards Cuplock
intermediate transoms are available for 2 boards and 3 boards.
Size: Cuplock Intermediate Transom 0.565 mm. (2 Board) Cuplock Intermediate Transom 0.795 mm (3 Board) |
||||||||
|
|
|
|
Cuplock Return Transom | |
||||||
|
||||||||
|
The Return Transom is used at the end of a
scaffold run where it meets another scaffold running at right angles to
it.
The U-shaped return section of the transom hooks over the ledger of the adjacent scaffold, closing off the gap between the two scaffold. Size: Cuplok Return Transom 1.3m |
||||||||
|
|
|
|
Ladder Access Transom | |
||||||
|
||||||||
|
The Ladder Access Transom is used to provide an opening in a bay allowing a ladder to pass through it. The L.A. Transom is attached to and spans between the ledgers in the bay. Size: Cuplok Ladder Access Transom 1.05m Cuplok Ladder Access Transom 1.27m Cuplok Ladder Access Transom 1.83m Cuplok Ladder Access Transom 2.44m |
||||||||
|
|
|
|
Hop-Up 1/2/3 Bracket | |
||||||
|
||||||||
|
Platform Brackets enable 1, 2 or 3 plank wide platforms to be placed between the scaffold and the workface. The blade end locates into the cup on the standard and the ends of the brackets are connected to each other with Tie Bars. Size Cuplok Platform Bracket - 1 Plank Cuplok Platform Bracket - 2 Plank Cuplok Platform Bracket - 3 Plank |
||||||||
|
|
|
Copyright
© Maini Construction Equipments Private Limited, All Rights
Reserved 
