|
|
 |
 |
 |
 |
 |
 |
   |
 |
 |
|
 |
Standard / Vertical |  |
||||||
|
||||||||
|
Cuplok spigotted standard/vertical is basically used in get in scaffolding work and also act as a base structure for Formwork strengthening applications. The cup joints are at every 500mm intervals. The inbuilt movable top cups are made for rough site handling. The welded bottom cups are made from high grade steel. Integral spigots are 150mm long and are provided at the top of each standard for making upright connections. The base and the spigots of every standard have 16mm diameter holes which enables use of locking pins to secure the standards wherever necessary.
Size:
Scaffolding Cuplock Standard 0.5m Scaffolding Cuplock Standard 1.0m Scaffolding Cuplock Standard 1.5m Scaffolding Cuplock Standard 2.0m Scaffolding Cuplock Standard 2.5m Scaffolding Cuplock Standard 3.0m |
||||||||
 |
|
 |
|
Ledger / Horizontal | |
||||||
|
||||||||
|
The ledger/horizontal are produced using the 48.3mm O.D. tube, it has forged steel blade ends which fitted into the bottom cups of the standards and are secured in place by the corresponding top cups. They are available in varied lengths to enable desired grid shapes for the scaffolding/Formwork. Since 1997, the ledger has been produced using thinner high grade steel tube. This has ensured easier handling of the higher ledger. Ledgers till 1997 were made from the thicker wall tube and weighed approximately 20% more than the weights stated below.
Size:
Cuplok Ledger 0.6m Cuplok Ledger 0.9m Cuplok Ledger 1.2m Cuplok Ledger 1.25m Cuplok Ledger 1.3m Cuplok Ledger 1.5m Cuplok Ledger 1.6m Cuplok Ledger 1.8m Cuplok Ledger 2m Cuplok Ledger 2.5m |
||||||||
|
|
|
|
Cuplock Transom | |
||||||
|
||||||||
|
The Cuplock transom is produced using conjoint twin structural angles fixed together and have a drop forged blade attached to each end. The 2.44m cuplock transom incorporates additional web member welded below the flange section for increased strength. The forged blades of the transom are fitted into the bottom cup and are secured using the top cup. The outside standing bottom leg angles sustain the steel planks in confined manner. The Cuplock transom is available in various lengths to suit scaffolding and Formwork applications. Size Cuplok Transom 0.31m Cuplok Transom 0.61m Cuplok Transom 0.83m Cuplok Transom 1.05m Cuplok Transom 1.27m Cuplok Transom 1.83m Cuplok Transom 2.44m |
||||||||
|
|
|
|
Cuplock Omega Transom | |
||||||
|
||||||||
|
The Cuplock Omega Transoms are manufactured from press bent section with flange type extensions on either side provides a reinforced back up to working platform with cuplock steel battens. Size:
Cuplock Omega Transom 0.9 M Cuplock Omega Transom 1.3 M Cuplock Omega Transom 1.8 M Cuplock Omega Transom 2.5 M |
||||||||
|
|
|
|
Cuplock Intermediate Transom | |
||||||
|
||||||||
|
These Cuplock intermediate transoms are used with Hop-up brackets. They are useful to make up for the distance between standards if it exceeds the span of scaffold boards. Cuplock intermediate transoms are used to secure the 2 boards and 3 boards.
Size: Cuplock Intermediate Transom 0.565 mm. (2 Board) Cuplock Intermediate Transom 0.795 mm (3 Board) |
||||||||
|
|
|
|
Cuplock Return Transom | |
||||||
|
||||||||
|
The Cuplock Return Transom is used at the end of a scaffold run where it meets another scaffold running at right angles to it. The U-shaped return section of the transom hooks over the ledger of the adjacent scaffold, to close the gap between the two scaffolds.
Size: Cuplok Return Transom 1.3m |
||||||||
|
|
|
|
Ladder Access Transom | |
||||||
|
||||||||
|
The Ladder Access Transom can provide a gap in a bay to allow a ladder to pass through it. The Ladder Access Transom is connected to and spans between the ledgers in the bay. Size: Cuplok Ladder Access Transom 1.05m Cuplok Ladder Access Transom 1.27m Cuplok Ladder Access Transom 1.83m Cuplok Ladder Access Transom 2.44m |
||||||||
|
|
|
|
Hop-Up 1/2/3 Bracket | |
||||||
|
||||||||
|
The hop-up brackets allow the 1, 2 or 3 plank broad platforms to be placed between the workplace and the scaffold. The blade end is fitted into the cup on the standard and the ends of the brackets are connected to each other with the help of Tie Bars. Size Cuplok Platform Bracket - 1 Plank Cuplok Platform Bracket - 2 Plank Cuplok Platform Bracket - 3 Plank |
||||||||
|
|
|
©
Maini Construction Equipments Private Limited. All Rights Reserved 
